How To Replace A Bathtub Spout Shower Diverter

Replace that Leaking Bathtub Shower Diverter for Good. Check the Screws First.

Shower Diverter Valve Fix Tub Spout Leak Causing Weak Shower

Replacing bathtub spout if water leaking or dripping from tub spout when shower is on.

How to replace a bathtub spout shower diverter. To be sure you purchase the correct replacement bring your old diverter with you to the store. There will be a small hole in the bottom of the tub spout if you see a screw you have a CC Slip Fit tub spout. How to Fix a Shower Diverter.

Slide the washer 3 into the front of the diverter gate 4 with the flat part of the washer 3 facing outward. Inspect the shower diverter for dirt and limescale. Replace your bathtub shower diverter quickly and easily.

Just loosen the setscrew usually with a hex wrench and pull the spout off the copper pipe that protrudes from the wall. Unthread the tub spout counter-clockwise to remove. For diverters with a rotating valve unscrew the nut at the stem of the diverter.

Unscrew the tub spout in a counterclockwise rotation until the tub spout is removed off of the brass adapter. Grease dirt and minerals from water can accumulate around the shower diverter. Locate the rubber washer and replace.

If you dont turn off the water supply water will seep out while youre working. Step 2 - Repair the Faulty Diverter. Take it to the hardware store and buy a suitable replacement.

It will make a mess and. Turn the faucet upward and pry apart the plastic prongs. Step 3 - Replace Diverter If Necessary.

Twist the spout as you pull and be gentle so you dont loosen any pipe connections inside the wall. This removes the potential for leakage. Option 5 Replace the whole spout Step 1.

It is important that all parts work without friction to ensure proper movement of all parts. Next reinsert the diverters underside portion by first putting in the spring and then the black washer. Nearly everyone has at one time or another used a shower where the diverter valve is worn out or broken causing water to drip out of the tub spout and weak water pressure from the shower head while you are showering.

If it has a gate-type valve unscrew the threaded tub spout. Use vinegar and a soft brush to clean any. Pull out the old metal shower diverter and slip the new one in its place.

Slide the lift rod 1 through the hole in the top of the spout 2. IPS Threaded - Threaded directly onto the pipe from the wall. July 11 2016.

Remove any caulking around the wall end of the tub spout with a putty knife or razor. Turn the wrench counterclockwise to unthread the spout from the stub-out pipe. Go through the diverter assembly and lubricate all moving parts to ensure proper motion and use.

Now you can turn the spout right side up and tighten it against the wall. Replacing a slip-on spout is easy. If there is no screw you have an IPS threaded tub spout.

For gate-type valves unscrew the threaded tub spout. Bring your new spout home and read the instructions. If your diverter has a rotating valve unscrew the nut at the stem of the diverter and remove the entire valve.

How to repair and fix not working diverter tub spout. Shut off your water supply and remove your spout from the wall. Then slide on the new spout and tighten the setscrew.

Remove the Spout Carefully scrape away the caulk where the spout meets the wall using a putty knife or utility knife Place a pipe wrench or channel-lock pliers around the spout and tighten it so it grips the fixture. Remove the entire valve. Use a 18 hexAllen wrench and un tighten the Allen screw counterclockwise.

Pull up on the lift rod 1 while gently prying the tabs apart on the diverter gate 4 using a small flathead screwdriver. Shut Off the Main Water Supply.

How To Replace A Bathtub Spout Diy Family Handyman